Hitro in varno nakupovanje
Brezplačna dostava po Sloveniji nad 100eur
Možnost vračila v 14 dneh
Description
300 ml
Oak
Cherry
Beech tree
PROPERTIES
Silicone for parquet is a one-component plastic-elastic sealant based on acrylic dispersion.
It is suitable for filling and sealing joints between parquet and laminate and between
slats and wall and for filling cracks in wood and floor coverings. Transfers to
10% expansion.
• Easy application.
• Does not slip in vertical racks.
• Good adhesion to porous materials.
• The mass can be applied to damp surfaces.
• Withstands dilatations up to 10%.
• Fully hardened mass is insensitive to water.
• Can be painted when hardened.
• High final hardness, can be ground.
• It is resistant to various atmospheric influences, sunlight and aging.
• Contains no solvents (VOC free).
• Fresh mass can be easily cleaned with water.
• Colors: beech, oak and cherry.
FIELD OF USE
• Filling and sealing joints between parquet and laminate and between slats and
the wall.
• Filling and sealing the joints between the parquet and the door frame. For filling
cracks in wooden floor coverings (laminates, wooden floors, cork, etc.).
INSTRUCTIONS FOR USE
Surface preparation:
The surfaces to be sealed must be solid, clean and free of dust and grease. Let's remove everything
loose and poorly bonded parts. Tekadom Parquet can be applied to a damp substrate.
Preparation of the rega and cartridge:
• Adhesion can be improved by using a primer made from sealant
Tekadom Parquet and water in a ratio of 1:3. Wet the surface with a brush or cloth and
let's leave it for a few minutes.
• Cut off the cartridge at the top near the thread, screw in the tip, which depending on the width of the joint or reggae
cut diagonally and insert into the gun. In case of interruption of work or we offer a discount on cartridge replacement
lever on the hand gun and pull the piston back. Apply the sealant as evenly as possible. A spatula can help when applying the mass.
• At the end, with a smoothing tool, namely a TKK trowel, or a finger that we
soaked in the Smoothing agent, we level the sealing compound before it does
foreskin. It is very important to press the sealant well onto the surface to be sealed.
• Clean the fresh mass and tools with water after use. The hardened mass can be removed mechanically.
Oak
Cherry
Beech tree
PROPERTIES
Silicone for parquet is a one-component plastic-elastic sealant based on acrylic dispersion.
It is suitable for filling and sealing joints between parquet and laminate and between
slats and wall and for filling cracks in wood and floor coverings. Transfers to
10% expansion.
• Easy application.
• Does not slip in vertical racks.
• Good adhesion to porous materials.
• The mass can be applied to damp surfaces.
• Withstands dilatations up to 10%.
• Fully hardened mass is insensitive to water.
• Can be painted when hardened.
• High final hardness, can be ground.
• It is resistant to various atmospheric influences, sunlight and aging.
• Contains no solvents (VOC free).
• Fresh mass can be easily cleaned with water.
• Colors: beech, oak and cherry.
FIELD OF USE
• Filling and sealing joints between parquet and laminate and between slats and
the wall.
• Filling and sealing the joints between the parquet and the door frame. For filling
cracks in wooden floor coverings (laminates, wooden floors, cork, etc.).
INSTRUCTIONS FOR USE
Surface preparation:
The surfaces to be sealed must be solid, clean and free of dust and grease. Let's remove everything
loose and poorly bonded parts. Tekadom Parquet can be applied to a damp substrate.
Preparation of the rega and cartridge:
• Adhesion can be improved by using a primer made from sealant
Tekadom Parquet and water in a ratio of 1:3. Wet the surface with a brush or cloth and
let's leave it for a few minutes.
• Cut off the cartridge at the top near the thread, screw in the tip, which depending on the width of the joint or reggae
cut diagonally and insert into the gun. In case of interruption of work or we offer a discount on cartridge replacement
lever on the hand gun and pull the piston back. Apply the sealant as evenly as possible. A spatula can help when applying the mass.
• At the end, with a smoothing tool, namely a TKK trowel, or a finger that we
soaked in the Smoothing agent, we level the sealing compound before it does
foreskin. It is very important to press the sealant well onto the surface to be sealed.
• Clean the fresh mass and tools with water after use. The hardened mass can be removed mechanically.
